埃德蒙顿华人社区-Edmonton China

 找回密码
 注册
查看: 3096|回复: 4

[技术互助] Any input on Cutler-Hammer Starter?

[复制链接]
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 12:56 | 显示全部楼层 |阅读模式
本帖最后由 td456 于 2010-3-26 14:14 编辑 1 V( {: _: L# g& d4 o4 }9 u

' R9 K1 d0 u, ?& OTwo  cutler –hammer advantage  starters are  doing the same thing:  |, b- g2 i7 f
After start 2-3 times, they will quit working, if you toggle the  start and stop buttons on DCS screen  , you will get another 2-3 running before they quit working again.
' e: x0 a4 U( A/ z3 NIt is a cycle.
2 i/ m: N* W0 p+ R  g/ Z4 k5 ~# E: [; m& z: ]
We isolate the network control and use the local start and stop only, the problem remains.2 w' B. E' K1 B) {5 b! I
Swap one of the defective buckets with a good one, the new bucket works fine.
1 n, ~* K/ B! A; {+ mThe problem should be inside the bucket.
/ `& V  T! i5 t5 v6 u0 ^
, k8 l. A, @, Z1 P- sWhen the problem happened, we observed that  the contactor has a pulling action but will not seal.9 Z1 d2 G2 R4 r
Use a terminating screw divers to push in the contactor, it will not seal either.6 S- \& G; L9 p, V5 F( i
Confirm with TECH support this should be a problem with the control circuit board inside the advantage starter, we  bought two new control circuit boards and replaced the old ones, the problem is still the same.
# o& X6 i& N1 X- A8 m5 B5 J' X5 X1 Q% N& u$ q% B% ~, o1 L
The next thing we can think of  is the coil, we took the coil out to have a close look.
+ M) w) r' |- R! \  f5 S' bThey  have a fork to pinch inside the two leads to make connection, it is not a good design at all. We soldered  the connection and tried again.
' |! b6 W! U8 i/ X* V It is getting better  this time, we have 7-8 times of running before it quit working.
( c! ~. H$ {1 d; }- l, H6 I- X4 f# V' Z  ~
The coil should be the problem, we ordered two of them. But it will take 5-6 weeks for us to get them. # J6 r8 \  e! G3 |' ?

8 }6 ~4 `0 J( J& E& a; c3 _Do you guys have any input on this issue?
鲜花(1) 鸡蛋(0)
发表于 2010-3-26 17:07 | 显示全部楼层
有时候主接触点太脏,也会造成启动器无法正常工作
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 17:37 | 显示全部楼层
本帖最后由 贾电工 于 2010-3-26 18:38 编辑
0 o0 G5 j: r& d* f2 p) M( S, D0 J
中国人在这里最好说中国话!说英语或想学英语请人到洋人论坛!
鲜花(7) 鸡蛋(0)
发表于 2010-3-26 17:42 | 显示全部楼层
Don't know cutler –hammer advantage  starters very well, but had been worked on AB switch gears for a little while, which has two different coils, one to pull the vacum bottles up which employs larger current, another one uses less current to hold the connection---if the second coil fails, it won't be able to seal the connection." K; Y# F/ K; ], p) v/ t  M' T
Since your cutler -hammer works couple times,  I guess 侠客行 is right, or the sealing connection is just worn out.
鲜花(0) 鸡蛋(0)
 楼主| 发表于 2010-3-26 17:55 | 显示全部楼层
2# 侠客行
4 @6 W0 _  e- }5 i  u# W5 K1 E也想到这一点,不过这是新装的设备。
, A( s, U- x* f+ d8 \# ^* i5 G$ U检查过触点没问题。
大型搬家
您需要登录后才可以回帖 登录 | 注册

本版积分规则

联系我们|小黑屋|手机版|Archiver|埃德蒙顿中文网

GMT-7, 2026-11-19 21:16 , Processed in 1.938061 second(s), 16 queries , Gzip On, APC On.

Powered by Discuz! X3.4

Copyright © 2001-2021, Tencent Cloud.

快速回复 返回顶部 返回列表