埃德蒙顿华人社区-Edmonton China

 找回密码
 注册
查看: 3099|回复: 4

[技术互助] Any input on Cutler-Hammer Starter?

[复制链接]
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 12:56 | 显示全部楼层 |阅读模式
本帖最后由 td456 于 2010-3-26 14:14 编辑 & s" U& ~+ f1 O6 D

0 D+ q" @+ q* z/ v, A/ rTwo  cutler –hammer advantage  starters are  doing the same thing:
4 z) [: d' L. w6 {$ a0 D) b After start 2-3 times, they will quit working, if you toggle the  start and stop buttons on DCS screen  , you will get another 2-3 running before they quit working again.   \  o4 k8 S6 x0 t7 q4 c$ d) F
It is a cycle.
  N8 J! n% F% m0 ~: ?8 e( `
( j# K# e) X4 g7 K6 jWe isolate the network control and use the local start and stop only, the problem remains.6 |: b% c) {* U7 p5 p
Swap one of the defective buckets with a good one, the new bucket works fine.
) K0 Q3 C% E% e& C) n2 DThe problem should be inside the bucket., i0 z! \2 V& e  a+ [0 j5 [" M  C
2 k" Z3 A; D4 m: Q2 d
When the problem happened, we observed that  the contactor has a pulling action but will not seal.! U! P% |1 D6 t  t+ \: H
Use a terminating screw divers to push in the contactor, it will not seal either.6 h# M3 C" _, L5 n- W, \* V
Confirm with TECH support this should be a problem with the control circuit board inside the advantage starter, we  bought two new control circuit boards and replaced the old ones, the problem is still the same.
* E' ~/ L5 V1 s: a' n# g% T7 F+ k) t/ R  C
The next thing we can think of  is the coil, we took the coil out to have a close look./ j+ n& ]9 \- m9 }
They  have a fork to pinch inside the two leads to make connection, it is not a good design at all. We soldered  the connection and tried again.4 Q4 C! L1 {! {) l+ [! s& V
It is getting better  this time, we have 7-8 times of running before it quit working. ' z, u! F* b8 q! v& i7 _

1 O  Y/ q3 f( u! o) ?The coil should be the problem, we ordered two of them. But it will take 5-6 weeks for us to get them. 3 h% V, Z* y* n% l
0 j! w; S) K2 A5 M: Z9 ]$ @7 y
Do you guys have any input on this issue?
大型搬家
鲜花(1) 鸡蛋(0)
发表于 2010-3-26 17:07 | 显示全部楼层
有时候主接触点太脏,也会造成启动器无法正常工作
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 17:37 | 显示全部楼层
本帖最后由 贾电工 于 2010-3-26 18:38 编辑 . t; m3 c- g9 s# ~+ ^

& c7 s3 B, H2 L( g0 c7 }6 x中国人在这里最好说中国话!说英语或想学英语请人到洋人论坛!
鲜花(7) 鸡蛋(0)
发表于 2010-3-26 17:42 | 显示全部楼层
Don't know cutler –hammer advantage  starters very well, but had been worked on AB switch gears for a little while, which has two different coils, one to pull the vacum bottles up which employs larger current, another one uses less current to hold the connection---if the second coil fails, it won't be able to seal the connection.' h$ a" T0 z3 q4 h" C
Since your cutler -hammer works couple times,  I guess 侠客行 is right, or the sealing connection is just worn out.
大型搬家
鲜花(0) 鸡蛋(0)
 楼主| 发表于 2010-3-26 17:55 | 显示全部楼层
2# 侠客行 7 G. `( c6 M3 N; H0 Q$ y! {5 c: ]
也想到这一点,不过这是新装的设备。4 l; z. K+ _( f9 }
检查过触点没问题。
您需要登录后才可以回帖 登录 | 注册

本版积分规则

联系我们|小黑屋|手机版|Archiver|埃德蒙顿中文网

GMT-7, 2026-11-19 21:31 , Processed in 0.110498 second(s), 15 queries , Gzip On, APC On.

Powered by Discuz! X3.4

Copyright © 2001-2021, Tencent Cloud.

快速回复 返回顶部 返回列表