埃德蒙顿华人社区-Edmonton China

 找回密码
 注册
查看: 3098|回复: 4

[技术互助] Any input on Cutler-Hammer Starter?

[复制链接]
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 12:56 | 显示全部楼层 |阅读模式
本帖最后由 td456 于 2010-3-26 14:14 编辑 9 i. W9 H9 S4 \( y" g% J2 s

1 S: ?2 k' U5 Z0 }) tTwo  cutler –hammer advantage  starters are  doing the same thing:
  h# I$ j% R/ d2 d* h* s After start 2-3 times, they will quit working, if you toggle the  start and stop buttons on DCS screen  , you will get another 2-3 running before they quit working again.
; c) P7 l1 ?. f: y, q) u8 {7 RIt is a cycle.
. b% _! A, [5 \! d- m3 H
2 J6 F' E' L) M& z& n( SWe isolate the network control and use the local start and stop only, the problem remains.7 j  Y  ]0 ?8 D/ S
Swap one of the defective buckets with a good one, the new bucket works fine.1 T, x/ E/ c  d
The problem should be inside the bucket.
8 X. {$ r3 g! d7 C+ t3 Y4 Q5 G
5 V- K" u0 G+ M6 FWhen the problem happened, we observed that  the contactor has a pulling action but will not seal.3 g( D' p$ R) r# m  c9 c) U
Use a terminating screw divers to push in the contactor, it will not seal either.1 N3 t8 q; O# t
Confirm with TECH support this should be a problem with the control circuit board inside the advantage starter, we  bought two new control circuit boards and replaced the old ones, the problem is still the same.
8 Q: e0 X! K& r( K
3 H2 i0 j7 I* YThe next thing we can think of  is the coil, we took the coil out to have a close look.8 e+ o; a. A( D3 c9 Y- G4 x
They  have a fork to pinch inside the two leads to make connection, it is not a good design at all. We soldered  the connection and tried again.
& P2 d1 m% i) W4 d9 b It is getting better  this time, we have 7-8 times of running before it quit working.
) T0 p0 v9 s% |; p
1 W# l, e  U4 |The coil should be the problem, we ordered two of them. But it will take 5-6 weeks for us to get them. 3 e, z2 F( \8 |1 k% c4 }2 J6 V
0 R2 m- k4 v9 @6 U
Do you guys have any input on this issue?
大型搬家
鲜花(1) 鸡蛋(0)
发表于 2010-3-26 17:07 | 显示全部楼层
有时候主接触点太脏,也会造成启动器无法正常工作
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 17:37 | 显示全部楼层
本帖最后由 贾电工 于 2010-3-26 18:38 编辑 0 t( Y' |1 B& Q, a  J- @
8 ^" D' V+ ~) a. p5 ?1 Y* P
中国人在这里最好说中国话!说英语或想学英语请人到洋人论坛!
鲜花(7) 鸡蛋(0)
发表于 2010-3-26 17:42 | 显示全部楼层
Don't know cutler –hammer advantage  starters very well, but had been worked on AB switch gears for a little while, which has two different coils, one to pull the vacum bottles up which employs larger current, another one uses less current to hold the connection---if the second coil fails, it won't be able to seal the connection./ _: l: M+ _$ w0 u. e4 t3 I. y) w
Since your cutler -hammer works couple times,  I guess 侠客行 is right, or the sealing connection is just worn out.
鲜花(0) 鸡蛋(0)
 楼主| 发表于 2010-3-26 17:55 | 显示全部楼层
2# 侠客行
: A  T3 T, ]7 X# ?# {. r9 J也想到这一点,不过这是新装的设备。$ R0 t* j0 z+ Z0 R! `! G
检查过触点没问题。
大型搬家
您需要登录后才可以回帖 登录 | 注册

本版积分规则

联系我们|小黑屋|手机版|Archiver|埃德蒙顿中文网

GMT-7, 2026-11-19 21:25 , Processed in 0.298074 second(s), 16 queries , Gzip On, APC On.

Powered by Discuz! X3.4

Copyright © 2001-2021, Tencent Cloud.

快速回复 返回顶部 返回列表