埃德蒙顿华人社区-Edmonton China

 找回密码
 注册
查看: 3097|回复: 4

[技术互助] Any input on Cutler-Hammer Starter?

[复制链接]
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 12:56 | 显示全部楼层 |阅读模式
本帖最后由 td456 于 2010-3-26 14:14 编辑
- V) t* M4 t" \2 p- S
. ^8 C6 D/ u( r6 W, `+ V: wTwo  cutler –hammer advantage  starters are  doing the same thing:
( i( h8 `+ v  Z" k' o6 ?; z After start 2-3 times, they will quit working, if you toggle the  start and stop buttons on DCS screen  , you will get another 2-3 running before they quit working again. $ n( Y5 s( V. A) n5 _
It is a cycle.
5 H; u, o' f+ g2 \8 p) J: S7 @/ L- n2 M, z
We isolate the network control and use the local start and stop only, the problem remains.1 k) e0 D6 L; g. x& H
Swap one of the defective buckets with a good one, the new bucket works fine.3 z4 s# B3 ~* A  i! ~# h- `4 G+ i
The problem should be inside the bucket.
  m5 ^7 @2 z% s6 w# Z- l5 ~
9 T7 W7 y; A. W$ i9 bWhen the problem happened, we observed that  the contactor has a pulling action but will not seal." G  f, K' \) c, a; l0 q
Use a terminating screw divers to push in the contactor, it will not seal either./ {# |( @7 N2 L( z# y# i
Confirm with TECH support this should be a problem with the control circuit board inside the advantage starter, we  bought two new control circuit boards and replaced the old ones, the problem is still the same.
: ?; r: @* j3 Z" B7 k1 k9 H* M9 l. ?8 Z. r5 l" k3 h6 d. `& `
The next thing we can think of  is the coil, we took the coil out to have a close look.
( J& x3 H) R0 C4 X4 n4 w4 l2 ZThey  have a fork to pinch inside the two leads to make connection, it is not a good design at all. We soldered  the connection and tried again.1 Y! [( G9 q3 ?' z
It is getting better  this time, we have 7-8 times of running before it quit working.
$ D, K7 ]( G4 f5 N* `0 P$ p5 v# t
The coil should be the problem, we ordered two of them. But it will take 5-6 weeks for us to get them. ' X- X* B' C8 P5 ~) J

9 {0 _: _6 C; O! ^/ w! k& xDo you guys have any input on this issue?
鲜花(1) 鸡蛋(0)
发表于 2010-3-26 17:07 | 显示全部楼层
有时候主接触点太脏,也会造成启动器无法正常工作
大型搬家
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 17:37 | 显示全部楼层
本帖最后由 贾电工 于 2010-3-26 18:38 编辑
9 M7 {  x: C, g* C8 N1 m8 u2 t6 }
中国人在这里最好说中国话!说英语或想学英语请人到洋人论坛!
鲜花(7) 鸡蛋(0)
发表于 2010-3-26 17:42 | 显示全部楼层
Don't know cutler –hammer advantage  starters very well, but had been worked on AB switch gears for a little while, which has two different coils, one to pull the vacum bottles up which employs larger current, another one uses less current to hold the connection---if the second coil fails, it won't be able to seal the connection.' o% T7 d, w" u, c7 ^
Since your cutler -hammer works couple times,  I guess 侠客行 is right, or the sealing connection is just worn out.
鲜花(0) 鸡蛋(0)
 楼主| 发表于 2010-3-26 17:55 | 显示全部楼层
2# 侠客行 0 U- B  Z; E4 h- W0 D' O: @
也想到这一点,不过这是新装的设备。
7 ~0 U* j$ s1 M: Y7 a检查过触点没问题。
您需要登录后才可以回帖 登录 | 注册

本版积分规则

联系我们|小黑屋|手机版|Archiver|埃德蒙顿中文网

GMT-7, 2026-11-19 21:23 , Processed in 0.211634 second(s), 16 queries , Gzip On, APC On.

Powered by Discuz! X3.4

Copyright © 2001-2021, Tencent Cloud.

快速回复 返回顶部 返回列表